Cedar smokehouse work in progress
- CrankyBuzzard
- Passionate
- Posts: 242
- Joined: Wed Jan 12, 2011 23:09
- Location: Texas
- Contact:
Cedar smokehouse work in progress
I've had this idea for quite a while now and finally got busy on it this week.
The smokehouse itself is 24" x 24" x 52" internal at the highest point. The main box is made from 3/4" plywood with a cedar plank overlay, raised roof, and rooftop.
Thus far the plan for this critter is to cold smoke salmon, and to work smoke the sausages that I make. However, I will also be able to smoke brisket, ribs, etc., as well since I'm putting a controlled heat source inside.
I'm in the process of making a smoke generator for the unit that will be quite a bit different than most have seen. Stainless steel housing, with the usual fish pump, but all beefed up. I'm a bit of a geek, so beware of what's to come!
The heat source for the smokehouse is a 2000 watt electric heating element hooked up to a PID so that I can control the temperature inside of the box. 3 J type thermocouples mounted in the rear of the box will average the temperature at the top, center, and bottom to determine the on/off of the heating element.
The build should be finished in the next week or so with the inaugural smoke coming shortly after...
Stay tuned!
Charlie
The smokehouse itself is 24" x 24" x 52" internal at the highest point. The main box is made from 3/4" plywood with a cedar plank overlay, raised roof, and rooftop.
Thus far the plan for this critter is to cold smoke salmon, and to work smoke the sausages that I make. However, I will also be able to smoke brisket, ribs, etc., as well since I'm putting a controlled heat source inside.
I'm in the process of making a smoke generator for the unit that will be quite a bit different than most have seen. Stainless steel housing, with the usual fish pump, but all beefed up. I'm a bit of a geek, so beware of what's to come!
The heat source for the smokehouse is a 2000 watt electric heating element hooked up to a PID so that I can control the temperature inside of the box. 3 J type thermocouples mounted in the rear of the box will average the temperature at the top, center, and bottom to determine the on/off of the heating element.
The build should be finished in the next week or so with the inaugural smoke coming shortly after...
Stay tuned!
Charlie
Charlie,
I am looking forward to the finished article and what it can do. I am very much interested in what you mean with having 3 J type thermo couples to regulated the internal temperature.
I can build and repair most things as I have every bit of equipment available but with electicity I am just a plain idiot.
Please let me/us have all this info if possible.
Thanks,
Jan.
I am looking forward to the finished article and what it can do. I am very much interested in what you mean with having 3 J type thermo couples to regulated the internal temperature.
I can build and repair most things as I have every bit of equipment available but with electicity I am just a plain idiot.
Please let me/us have all this info if possible.
Thanks,
Jan.
- CrankyBuzzard
- Passionate
- Posts: 242
- Joined: Wed Jan 12, 2011 23:09
- Location: Texas
- Contact:
Jan, I'll post the schematics of the electronics once it is all finalized. I've decided to add switches to control the air pump and smoke generator heater. Yep, electric starter for the chips/pellets too. This has been an ongoing plan for a while now.
Ross, I figure if I keep that igloo cooler full of ice cold beer I should be fine.
The base will be made from cedar as well. If you look at the picture and see the bottom 6" are bare with no trim, it's because that portion will set down into the cedar frame base. To the right of the smokehouse will be a granite countertop that I had cut down when we had the countertops in the kitchen replaced last year.
The picture makes it look like I have really tight joints on the build, in all actuality, it's not so pretty. Working with this rough cedar that was cut and designed for fence material is a PITA. Next time ill use dimensional lumber for sure!
Charlie
Ross, I figure if I keep that igloo cooler full of ice cold beer I should be fine.
The base will be made from cedar as well. If you look at the picture and see the bottom 6" are bare with no trim, it's because that portion will set down into the cedar frame base. To the right of the smokehouse will be a granite countertop that I had cut down when we had the countertops in the kitchen replaced last year.
The picture makes it look like I have really tight joints on the build, in all actuality, it's not so pretty. Working with this rough cedar that was cut and designed for fence material is a PITA. Next time ill use dimensional lumber for sure!
Charlie
- CrankyBuzzard
- Passionate
- Posts: 242
- Joined: Wed Jan 12, 2011 23:09
- Location: Texas
- Contact:
More work today
Got the house completely trimmed out today, temp installed the burner for fit purposes, door is on, and almost ready to smoke!
I wanted a break from the power tools so I put the smoke generator together and have it in test run mode now. It's rocking along really well!
http://i539.photobucket.com/albums/ff36 ... 3C3AF5.mp4
Click the link above for a video of the smoke generator in action.
Hope to get the base done this week and have the inaugural smoke next weekend!
Charlie
I wanted a break from the power tools so I put the smoke generator together and have it in test run mode now. It's rocking along really well!
http://i539.photobucket.com/albums/ff36 ... 3C3AF5.mp4
Click the link above for a video of the smoke generator in action.
Hope to get the base done this week and have the inaugural smoke next weekend!
Charlie
- Chuckwagon
- Veteran
- Posts: 4494
- Joined: Tue Apr 06, 2010 04:51
- Location: Rocky Mountains
- CrankyBuzzard
- Passionate
- Posts: 242
- Joined: Wed Jan 12, 2011 23:09
- Location: Texas
- Contact:
Thanks CW, I was blessed with many different talents and try to use them well. My work never looks as nice as I imagine it will, but it's functional!
Learned a lesson with the smoke generator tonight... The wood chips have a tendency to "bridge" on me and I lose my burn after about 3 hours.
Guess ill have to buy some pellets and see how those work.
Anyone tried sawdust in a vertical smoke generator?
Charlie
Learned a lesson with the smoke generator tonight... The wood chips have a tendency to "bridge" on me and I lose my burn after about 3 hours.
Guess ill have to buy some pellets and see how those work.
Anyone tried sawdust in a vertical smoke generator?
Charlie